![]() The network map generated by this monitor normally shows 7 devices connected to the router and provides details such as the MAC address and ip number of each. As I said, Netgear provides a network monitor they call Genie. My problem at the moment is that, although they are all connected, they are not behaving like a LAN. I’ve used this arrangement for the past few years with Windows and Ubuntu and have had no problems. Yes, I can ping all the devices, and yes, they are all connected to the same wireless network, along with some other devices such as a smart TV and Roku. I believe this is the first time I have used a forum to ask for technical help, and it is apprent that I don’t know how they work. I understand that ignorance is not an excuse, but it is a reason. RX bytes:9727606 (9.2 Mb) TX bytes:50642 (49.4 Kb)Īgain my apologies for sloppy use of terminology and failure to observe protocol. TX packets:653 errors:0 dropped:0 overruns:0 carrier:0 RX packets:70582 errors:0 dropped:0 overruns:0 frame:0 TX packets:80798 errors:0 dropped:0 overruns:0 carrier:0 ![]() RX packets:161943 errors:0 dropped:0 overruns:0 frame:0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 TX packets:390 errors:0 dropped:0 overruns:0 carrier:0 RX packets:390 errors:0 dropped:0 overruns:0 frame:0 I’m sure this is just a configuration problem, but I don’t know how to correct it.īy “Server” I meant my desktop computer on whcih openDUSE is installed and has always been the center of LANs I used. That’s why my subject is “How to create a LAN.” Both printers and the other computer show that they are connected to BETRONA, but they are not connected to each other. Under both Windows 8.1 and Ubuntu the LAN was set up automatically. The Brother printer is routed to the HP connection and prints anything sent to it on the HP. The NETGEAR Genie program reports that my internet connection is fine but that my WiFI connection is “not enabled.” OpenSUSE, version 13.2, shows both printers in YAST, but only the HP, which is both wired and wireless, prints. However they do not/cannot connect to each other. Each of these devices can connect to the internet through that network. I have 4 devices connected wirelessly to a Netgear Nighthawk AC 1000 smart wifi router which generates a wifi connection called BETRONA. I consider my question trivial and most probably answered in some documentation that I haven’t read. I would appreciate it if someone would direct me to a source of current information. for example the command: ifconfig eth0 192.168.0.1 netmask 255.255.255.0 up produces this responseĪpparently the advice I’m getting is out of date. When I try to use the command lines suggested, they don’t work either. All it provides is a settings applet that allows very few changes and no opportunity to make a new connection. For example, they say a right click on NetworkManager in the Active connections list will enable me to beging making a new network, but all that comes up is two colums of Details with the ability to moe items from one column to another. The manual suggestions all involve steps to take using Network Manager, but the instructions it gives do not produce the results they show. I have deactivated wicked and am using only Network Manager. I’ve consulted the opensuse manual on networking and also the web. ![]() I have diisabled the firewall because I know it is often the source of connection problems. ![]() All the machines operate as they always have. The computer I want to use as a server and the Brother printer also have a ethernet connections. I have a simple arrangement of 2 computers and 2 wireless multipurpose machines, an HP 8500 Officejet Pro and a Brother 2280DW. I had no trouble connecting to the internet with Network Manager, but I am unable to configure the adapter to create a local network. I’ve recently changed from Ubuntu to Opensuse, and I’m unable to establish a LAN. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |